Our lives are kept in order as we open and close our garage doors. The garage door can be raised or lowered by pressing a button or using a combination of keys on a keypad. It helps protect our belongings.
It fails to open or close properly. It can also impact our daily lives.
A blinking light is one of the most common problems with garage door openers. When your garage door opener light suddenly flashes and does not open, you must take appropriate action. Although your garage door should still work if you hold the wall button down, it will be unable to open unless you fix it as soon as possible. Do not panic. Slow down and take the right action if your garage door light blinks
How Garage Door Sensors Works
A photo eye sensor will usually be fitted to the garage door sensor. Photo eye sensors can detect objects and people. An infrared beam connects two photo eyes. The sensor won’t work if the light stops running between the two eyes. After you touch the remote, the track and pulley system will lift and lower the garage door if the area is clear.
Garage Door Sensors Blinking Red- Basic Reasons
Blockage of the sensor’s path
Make sure nothing blocks the sensor’s beam. It will cause the door not to close as if your car is inside the doorway. Avoid malfunctions by cleaning your sensor lenses now and again. Sensor lenses can become covered in dirt and dust without you realizing it. If you don’t maintain your sensor lenses for a long time, or if there is a lot of pollution and wind in the area, this can lead to dirt buildup. It causes dirt and dust to build up on your sensor’s lenses, preventing them from functioning properly.
Moisture can affect the sensor
sometimes wetness from rain or your water sprinklers could get in and around garage door sensors. It could be the cause of the malfunction. Make sure that your sensors are dry.
Sensor alignment issue
Your garage door sensors might be blinking red due to misalignment. You should ensure that the sensors are aligned in this instance.
Sensor damage
As with all electronic components, wear and can cause damage to your garage door sensor. If you have been using the sensor for more than ten years, it is worth checking for damaged wires.
Understanding the LED light indicator.
An LED light indicator is used to indicate garage door openers. It can find it on the bottom panel or the back of the unit. Depending on the problem, the LED light indicator will blink several times. This indicator is great for diagnosing the problem with your garage opener. Here are some common problems that most garage door openers have:
- 1 Flash indicates that a wire is broken or disconnected and will need to be replaced or reconnected.
- 2 Flashes indicate that the safety wire is shorted or that the black/white wires have been reversed. It will need to correct.
- Four Flashes indicate that safety sensors are not aligned properly and must be re-aligned, so the green light continues to glow continuously.
Garage Door Sensor Blinking Red- Troubleshooting
Check the Sensors
- A problem with your garage door sensors could prevent your garage door’s closing completely.
- Each garage door is equipped with a safety sensor mounted on the tracks on the floor. These sensors provide security for your children, pets, and any other objects in the garage door’s path and prevent them from falling on them.
- These sensors can also send incorrect signals if they are damaged. To ensure that the lenses are clean and free from dust or dirt, you should inspect them regularly. To remove dirt and improve the efficiency of the lens operation, you should wipe them with a soft cloth.
- You should also check the indicator’s blinking color. It is functional if it emits green light. Check for misalignment and sensor wires. Also, make sure the lenses are clean when the red light blinks.
Remote
- Your remote can control your garage door’s opening and closing. Sometimes, however, the remote may not work properly to close your garage door. The problem is with the battery.
- A power surge could also be a problem that can wipe out your garage door’s memories. First, check the batteries and then replace them. If the remote does not respond, you can reprogram it.
- Determine the location of the garage opener’s lean button to program your remote. Use a ladder to remove the light cover to reach the garage door opener mounted on a ladder. A large “learn button” will appear. Hold the button down.
- Identify and press the lean button of your remote. The light will flash when you press both buttons simultaneously. You will have programmed the remote.
The Trolley
- The trolley mechanism connects your garage door to the opener. The trolley mechanism is equipped with a rope that connects or disconnects the garage door opener’s chain.
- If your trolley moves easily by hand when you push it, there’s a chance that it is in bypass mode. Pull the rope towards the door to get the trolley out of bypass mode. Once activated, the trolley latches and works effectively.
See the tracks and rollers.
- Even if the sensors work, any obstruction can cause your garage door to stop working. Damaged rollers can also affect the functionality of your garage door.
- Once you are satisfied that your sensors work, check the tracks and rollers to ensure there is no damage. Use clamps to fix any bent tracks.
- Ensure your garage door rollers have been properly lubricated to minimize friction between garage doors and surfaces. Silicone-based grease can be used as a lubricant.
What steps are required to replace garage door sensors?
- It is easy and takes only 15-20 minutes. These tools are needed to replace garage door sensors.
- Stairs
- Pliers
- Work gloves
- Tweezers
- Protective glasses
- Blue wire nuts
Steps
- Locate the garage remote control power cord using a ladder and unplug it. Next, unscrew the wing nuts and take the brackets off the sensors.
- The wire that connects to the sensor should be cut to approximately 1 inch. It will use this file for attaching the new sensor. Make sure you leave enough room. The blue nut can use to connect the black-white control wire from your new sensor to the older black-white wire. Continue with the second sensor.
- After they are connected, connect the white control wire. Use the other nut to connect the blue wire to the sensor. Continue on both sides.
- They do well when the green and red lights are on constantly.
- To test the sensors, place an object between the two to block the beam. The remote control uses to close the garage door. The motor lights should flash, and the door should not be closed.
How to test a garage door sensor
- You now better understand garage door sensors and how to troubleshoot common problems. It is time to test the functionality of your sensor. It will help you identify if your garage sensor is defective and if your troubleshooting was successful.
- To test your garage doors sensor grab any object you like, such as a cardboard container, and place it in the sensors’ path. Then close the garage door.
- If the door turns in the opposite direction, your sensor has detected the obstruction and is working properly. If the door closes around the box, you will need to investigate the problem further with your sensor.
Conclusion
As important as garage door sensors, it lets you know how well your garage door works. To avoid malfunctions or damage to your garage door, keeping them in a safe environment is important. These issues can be fixed by homeowners who can troubleshoot. Homeowners should contact a licensed professional to repair the damage if the situation is difficult. It can cause loss of life, property, or pets, which no homeowner wants to see in their home.
Leave a Reply